ATV12H075M2 Speed ​​variator for 0.75kW tri-motor - 220V single power supply - Altivar ATV12 Schneider

Main Product range Altivar 12 Product type or equipment Variable speed drive Product destination Asynchronous motors Specific product application Simple machine Construction variant With heat sink Component name ATV12 Lot quantity Pack of 1 EMC filter Integrated integrated fan Without Number of phases network Single-phase [Us] supply voltage 200…240 V - 15...10% motor power kW 0.75 kW motor power hp 1 hp Communication protocol Modbus line current 10.2 A at 200 V8.5 A at 240 V speed range 1…20 transient overtorque 150…170% of the motor's nominal torque depending on the drive rating and the motor type control profile for asynchronous motor Quadratic voltage/frequency ratio Voltage/frequency ratio (V/f) Control vector of current flow without sensor IP degree of protection IP20 without shutter on the upper part Acoustic pressure 0 dB Additional Power frequency 50/60 Hz +/- 5% type of connector 1 RJ45 (on front) for Modbus physical interface 2-wire RS 485 for Modbus RTU transmission frame for Modbus transmission speed 4800 bit/s9600 bit/s19200 bit/s38400 bit/s number of addresses 1…247 for Modbus communication service Read holding registers (03) 29 wordsWrite of single register (06) 29 wordsWrite multiple registers (16) 27 wordsRead/write multiple registers (23) 4/4 wordsIdentification of reading device (43) presumed line short-circuit current 1 kA permanent output current 4 .2 A at 4 kHz maximum transient current 6.3 A for 60 s frequency converter output frequency 0.5...400 Hz nominal switching frequency 4 kHz switching frequency 2...16 kHz adjustable 4...16 kHz with braking torque Up to 70% of the rated motor torque without braking resistor motor slip compensation Factory predefined Adjustable output voltage 200 to 240 V 3 phases electrical connection Terminal block, clamping capacity: 3.5 mm², AWG 12 (L1, L2, L3, U, V, W, PA, PC) Tightening torque 0.8 N.m Electrical isolation between power supply and power supply control Internal power supply for the reference potentiometer: 5 V DC (4.75…5 .25 V), <10 mA, protection type: overload and short circuit protection Internal power supply for logic inputs: 24 V DC (20.4…28.8 V), <100 mA, protection type: overload protection overloads and short circuits Number of analog inputs 1 type of analog input Configurable current AI1 0...20 mA 250 Ohm Configurable voltage AI1 0...10 V 30 kOhm Configurable voltage AI1 0...5 V 30 kOhm number of digital inputs 4 type of digital input Programmable LI1...LI4 24 V 18...30 V digital input logic Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhmPositive logic (source), 0…< 5 V (state 0), > 11 V (state 1) sampling time 20 ms, tolerance +/- 1 ms for logic input10 ms for analog input linearity error +/- 0.3% of the maximum value for analog input Number of analog outputs 1 type of analog output AO1 voltage configurable by software: 0...10 V, impedance: 470 Ohm, resolution 8 bitsAO1 current configurable by software software: 0...20 mA, impedance: 800 Ohm, resolution 8 bits number of digital outputs 2 type of digital output Digital output LO+, LO-Protected relay output R1A, R1B, R1C 1 C/O minimum switched current 5 mA at 24 V DC for logic relay maximum switched current 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay 3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay 4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay acceleration and deceleration ramps Linear from 0 to 999.9 sUS stopping braking 4 x 2.5 mm² + 2 x 1 mm² + 2 x 0.14 mm², <30 s protection type Power supply overvoltage Power supply undervoltage Overcurrent between output phases and earth Overheating protection Short circuit between motor phases Against loss of three-phase input phase Thermal protection of the motor via the drive by continuous calculation of I²t frequency resolution Analog input: A/D converter, 10 bits Display unit: 0.1 Hz time constant 20 ms +/- 1 ms for reference change CE marking Mounting position Vertical +/- 10 degrees Height 143 mm Width 72 mm Depth 131.2 mm Product weight 0.8 kg Functionality Basic specific application Commercial equipment Variable speed drive application selection Commercial equipment MixerCommercial equipment Other Application Textile Stretching Type Motor Starter Speed ​​Variator