ATV12H037M2 Speed ​​variator for 0.37kW tri-motor - 220V single power supply - Altivar ATV12 Schneider

Main Product range Altivar 12 Product type or equipment Variable speed drive Product destination Asynchronous motors Specific product application Simple machine Construction variant With heat sink Component name ATV12 Lot quantity Pack of 1 EMC filter Integrated integrated fan Without Number of phases Single-phase network [Us] supply voltage 200...240 V - 15...10% motor power kW 0.37 kW motor power hp 0.55 hp Modbus communication protocol line current 5.9 A at 200 V4.9 A at 240 V speed range 1…20 transient overtorque 150…170% of the motor's nominal torque depending on the drive rating and the motor type control profile for asynchronous motor Vector control of current flow without sensorVoltage/frequency ratio ( V/f) Quadratic voltage/frequency ratio IP degree of protection IP20 without shutter on the upper part Acoustic pressure 0 dB Additional Power frequency 50/60 Hz +/- 5% type of connector 1 RJ45 (on front) for Modbus 2-wire physical interface RS 485 for Modbus RTU transmission frame for Modbus transmission speed 4800 bit/s9600 bit/s19200 bit/s38400 bit/s number of addresses 1…247 for Modbus communication service Read holding registers (03) 29 wordsWrite single register (06) 29 wordsWrite multiple registers (16) 27 wordsRead/write multiple registers (23) 4/4 wordsRead device identification (43) prospective line short circuit current 1 kA output current permanent 2.4 A at 4 kHz maximum transient current 3.6 A for 60 s output frequency of the speed controller 0.5…400 Hz nominal switching frequency 4 kHz switching frequency 2...16 kHz adjustable4... 16 kHz with braking torque Up to 70% of rated motor torque without braking resistor motor slip compensation Adjustable Factory preset output voltage 200 to 240 V 3 phases electrical connection Terminal block, clamping capacity: 3.5 mm², AWG 12 (L1, L2, L3, U, V, W, PA, PC) Tightening torque 0.8 N.m Electrical isolation between power supply and control power supply Internal power supply for the reference potentiometer: 5 V DC (4.75 …5.25 V), <10 mA, type of protection: overload and short-circuit protection Internal power supply for logic inputs: 24 V DC (20.4…28.8 V), <100 mA, type of protection: protection against overloads and short circuits Number of analog inputs 1 type of analog input Configurable current AI1 0...20 mA 250 Ohm Configurable voltage AI1 0...10 V 30 kOhm Configurable voltage AI1 0...5 V 30 kOhm number of digital inputs 4 type of digital input Programmable LI1...LI4 24 V 18...30 V digital input logic Negative logic (sink), > 16 V (state 0), < 10 V (state 1 ), input impedance 3.5 kOhmPositive logic (source), 0…< 5 V (state 0), > 11 V (state 1) sampling time 20 ms, tolerance +/- 1 ms for logic input10 ms for analog input linearity error +/- 0.3% of maximum value for analog input Number of analog outputs 1 type of analog output AO1 software configurable voltage: 0...10 V, impedance: 470 Ohm, resolution 8 bitsAO1 current software configurable: 0...20 mA, impedance: 800 Ohm, resolution 8 bits number of digital outputs 2 type of digital output Digital output LO+, LO-Protected relay output R1A, R1B, R1C 1 C/O minimum switched current 5 mA at 24 V DC for logic relay maximum switched current 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay3 At 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay4 At 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay acceleration and deceleration ramps Linear from 0 to 999.9 sSU braking d shutdown 4 x 2.5 mm² + 2 x 1 mm² + 2 x 0.14 mm², <30 s type of protection Power supply overvoltage Power supply undervoltage Overcurrent between output phases and earth Overheating protection Short circuit between phases of the motor Against loss of three-phase input phase Thermal protection of the motor via the drive by continuous calculation of I²t frequency resolution Analog input: A/D converter, 10 bits Display unit: 0.1 Hz time constant 20 ms +/ - 1 ms for reference change CE marking Mounting position Vertical +/- 10 degrees Height 143 mm Width 72 mm Depth 121.2 mm Product weight 0.7 kg Functionality Basic specific application Commercial equipment Variable speed drive application selection Commercial equipment MixerCommercial equipment Other applicationTextile Stretching motor starter type Variable speed drive